1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

H9S problem

Discussion in 'Zgemma H9S - 4K' started by castro, May 29, 2018.

  1. castro

    castro Registered

    29
    0
    1
    Male
    tinkering with the settings of my new zgemma h9s, i must've enabled additional voice-over for the visually impaired... can't find how to get rid of it again... :eek: anyone know?
     
  2. jigger121

    jigger121 Registered

    Press audio on your remote and then change from nar
     
  3. castro

    castro Registered

    29
    0
    1
    Male
    thanks, fellow celtic supporter! what the heck is 'nar'?
     
  4. gray1313

    gray1313 TK Veteran

    666
    144
    83
    narrative
     
  5. castro

    castro Registered

    29
    0
    1
    Male
  6. benijofar

    benijofar Super Moderator Staff Member Forum Supporter

    2,584
    1,741
    133
    Male
    {Lazing Around
    Costa Blanca ...Spain
    Don't do the updates as they corrupted the build last time i tried.
     
    castro likes this.
  7. castro

    castro Registered

    29
    0
    1
    Male
    ok, cheers! no rush, but if some time someone could point me in the right direction how to do this properly, i'd really appreciate it.
     
  8. cactikid

    cactikid VIP Member

    16,106
    1,018
    133
    i like corruption how much is it worth:eek::D
     
  9. castro

    castro Registered

    29
    0
    1
    Male
    there'll be some reward, no worries! ;)
     
  10. cactikid

    cactikid VIP Member

    16,106
    1,018
    133
    never factory reset a zgemma ,just follow the flashing guides for the zgemma and low level format usb ,umpteen threads in there with same issues,and usb only inserted when box is powered off any other usb devices removed and setup from scratch.
    Save any lines and cfg files if needed before flashing.
     
    castro likes this.
  11. castro

    castro Registered

    29
    0
    1
    Male
    ok, cheers for that! will try tomorrow. all threads i could find relate to former zgemma models...
     
  12. cactikid

    cactikid VIP Member

    16,106
    1,018
    133
    Usually done the same way but files need to suit the box you want to flash,boxes can be a fecker to flash with usb sticks not seen and to use a good quality usb stick 8gb kingston ,cruzer,and integral i use for my boxes.
     
  13. castro

    castro Registered

    29
    0
    1
    Male
    thanks mate! will do my best and let you know how i get on. wish me luck. :D
     
  14. cactikid

    cactikid VIP Member

    16,106
    1,018
    133
    all the best
     

    Attached Files:

  15. castro

    castro Registered

    29
    0
    1
    Male
    So, I tried and tried and tried again flashing my new H9S box. Online and using usb, nothing worked. - Remember Homer Simpson: "So you've tried your best and failed miserably. The lesson is: never try!" :D

    I guess I'll just have to wait for an improved update.
    Still, thanks for all support!
     
  16. cactikid

    cactikid VIP Member

    16,106
    1,018
    133
    What usb are you using as many have issues.
     
  17. castro

    castro Registered

    29
    0
    1
    Male
    used a decent toshiba 8GB stick, properly formatted to FAT32 and all. But "took your advice onboard and ordered an 8GB Kingston data traveller today. Maybe that'll fix it.
     
  18. castro

    castro Registered

    29
    0
    1
    Male
    Yes, just found this here: "Unzip the download and put the folder and other files onto USB. Turn off box insert USB. Press the reset button on back of box opposite side to power button. Hold reset button while powering on and keep pressing reset button till air digital icon on front panel changes colour then release and wait for it to boot up."

    Will try that! (didn't realise there's a reset button!) Cheers!