Possible to use cccam and newcamd together?

[dools]

Hey,

Is it possible to use two lines C & N together on a Zgemma box. If one drops off the other kicks in?

Cheers,
Dools

 

[kiddac]

just stick them both in your CCcams.cfg file.

C: fasfasdfasdf
N: sfsfsdfas

The good thing about cccams is the cccaminfo button (yellow). Press that then go into servers and it will either show a red or green light next to every line you have in your config file

 

[dools]

If one drops off does the other kick in automatically? Do I have to switch over myself? Cheers

Sent from my SM-G900F using Tapatalk

 

[dools]

Is it possible to use two newcamd lines together? Have 2 lines entered in the same newcamd.list beginning with CWS= from two different servers. Does it pick one over the other. Can i view which one is running through Openvix interface like you can in CCcam Info on Openvix. Running mgcamd.1.35a heard this is better than CCam2.3.0. I have two newcamd lines together but still getting scrambling? Thanks for help

 

[FreeUK]

The problem with using an N: line in Cccam is you will not benefit from the Cache ECM server that your line provider uses with it produces almost glitch free without it and you could have some small freezes, you can use both an N: & C: line in Mgcamd your N: goes into the usual file place newcamd.list and then place your C: line in the cccamd.list if you dont have one create one also make sure that in mg_cfg option G: {33} is that.

Job sorted you now benefit from any Oscam cache and run your C: line at the same time

 

[dools]

Hey Currently in my mg_cfg i have G: { 01 }
This should be G: { 33 }
Just to make sure and this will work both CWS line in newcamd.list and C line in cccamd.list
Thanks for your help.

 

[FreeUK]

Yes that is correct both will work when G: is changed to G: {33}.

i also uploaded a fully working set of MGcamd files here: http://www.techkings.org/zgemma-star-h-2h/83459-cannot-find-use-mgcam-1-38-a-2.html#post463131

if you want to replace your existing ones just make sure you backup the relevant line information, those files have been configured to work with N: and C: and both sat and Cable

 

[dools]

Hey. If i get a NLine instead of a CLine do i just put the NLine in the cccamd.list?
Many thanks

 

[FreeUK]

you can but you would have to enter it as a standard N: line with no CWS = think of it this way the cfg files speak for themselves as in:

cccamd for C: lines and newcamd for N: lines

 

[dools]

Okay this is the way i have it at the moment. I know i have one too many. I feel a bit stupid so thanks for the time. I find this so interesting:anyonethere:
_____________________

cccamd.list - N: (A)
_____________________

newcam.list CWS: (B)

& Converted N: to CWS (C)
_____________________

I know B is needed but should i have it with A to take advantage of the Cache EMC Server you spoke of that is so important.

Cheers

---------- Post Merged at 10:27 PM ----------

Okay my confusion comes from my provider. I have a login panel to control my lines.

If i download a C:line it has N at the start
If i download a N:line it has CWS at the start.

Cheers

 

[dsayers2014]

So there nlines just use the CWS one and put it in newcamd.list

 

[dools]

Okay Thanks.

Have two providers.
Provider 1 provides a CWS file to me. I put this in the newcamd.list
Provider 2 Gives me the two options which i see now are both NLines.

If i put provider 2 CWS line in the newcamd.list will it increase my overall quality I have take on board the very helpful FreeUK and mg_cfg set to G: { 33 }
Will this help with the overall quality?

Many thanks.

 

[dangerous]

i also uploaded a fully working set of MGcamd files here: Cannot find or use mgcam 1.38

Many thanks for this info FreeUK, ive just used these files to get my N line (for cable) and my C line (for sat) into Mgcamd. Works a treat 👍👍