What's new
By:
Filters

WooshBuild Wooshbuild Infinity Support Thread

Status
Not open for further replies.
Anybody know how to make the TV Channel Name remain on display on the front LED panel of the Mut@nt HD51 with Wooshbuild? At the moment it can display time and/or channel number but would prefer the channel name. Been through the settings and nothing....
 
Can someone advice me please. I'm flashing whooshbuild infinity on my zgemma h9s using the openwebif terminal method. all going well until loading plugins...it has now been stuck on 'configuring enigma2-plugin-extensions-epgimport for around 10 minutes and doesn't seem to be moving on...is this normal or has it froze?

Tried several times now and sticks at the same point...what can I do?
 
Last edited:
Did you remove the usb that you flashed open atv with? Sometimes it confuses the box if left in.
 
reflash openatv6.2 and start again, my H2h did this when i took the USB out after openatv had been flashed, on the third attempt, I left the usb in and it went swimmingly

pabloescaban said:
reflash openatv6.2 and start again, my H2h did this when i took the USB out after openatv had been flashed, on the third attempt, I left the usb in and it went swimmingly
Click to expand...

so pick the bones from these two replies
 
Last edited by a moderator:
The next step is installing the picons I think.
What happens if you turn the box off and on again. Where does that leave you. Im hoping you just have to run a channel scan manually.
 
Phil99z said:
Anybody know how to make the TV Channel Name remain on display on the front LED panel of the Mut@nt HD51 with Wooshbuild? At the moment it can display time and/or channel number but would prefer the channel name. Been through the settings and nothing....
Click to expand...
have you had any luck in solving this? i have the same box with the same issue
 
wheelo said:
Did you remove the usb that you flashed open atv with? Sometimes it confuses the box if left in.
Click to expand...
No, the box came with open atv already on it. only put usb in when whooshbuild asked me to

makido said:
The next step is installing the picons I think.
What happens if you turn the box off and on again. Where does that leave you. Im hoping you just have to run a channel scan manually.
Click to expand...
When I turn the box off/on again it just begins the install again with whooshbuild infinity screen then onto EasySetup, asking to insert usb....

pabloescaban said:
reflash openatv6.2 and start again, my H2h did this when i took the USB out after openatv had been flashed, on the third attempt, I left the usb in and it went swimmingly
Click to expand...
Tried flashing the box but the AIR icon doesn't go red when I hold in reset button and turn box on...
 
Last edited by a moderator:
If you exit the wizard where the infinity wizard starts (think its red button) you will be able to reflash it online
Blue button > flash online/local > green (online)
If you only see 6.1 available press the blue button then you should see 6.2
 
pabloescaban said:
you need to flash openatv 6.2 to the box, then follow the infinity instructions
http://images.mynonpublic.com/openatv/current/index.php?open=zgemmah9s
download these flash files, unzip and put on a formatted usb stick
flash in the normal way
Click to expand...
ok will try. Couldn't get the box into flash mode before

makido said:
If you exit the wizard where the infinity wizard starts (think its red button) you will be able to reflash it online
Blue button > flash online/local > green (online)
If you only see 6.1 available press the blue button then you should see 6.2
Click to expand...
will give that a go, thanks

makido said:
If you exit the wizard where the infinity wizard starts (think its red button) you will be able to reflash it online
Blue button > flash online/local > green (online)
If you only see 6.1 available press the blue button then you should see 6.2
Click to expand...
tried to flash online but keep getting a message "not enough space, you need at least 300mb" !!!
 
Last edited by a moderator:
makido said:
plug your usb in back of the box then check its mounted as media/hdd
red button > plugins > mount manager
Click to expand...
I've got the box to now flash 6.1 online..fingers crossed

Auccsessfully flashed to 6.1 will try whooshbuild again :)

GRRRR...stuck at the same stage again: configuring enigma2-plugin-extensions-epgimport.
:(
 
Last edited by a moderator:
makido said:
Can you get to 6.2 from flash online
Just flashed to infinity so it is working
Click to expand...
just flashed 6.2 now..waiting for box to boot up again.. beganto install whooshbuild then it jumps back to the configuration screen: HDMI or REC < whatever that is
 
Last edited:
Johnsmith99 said:
just flashed 6.2 now..waiting for box to boot up again.. begins whooshbuild install then jumps back to the configuration screen: HDMI or REC < whatever that is
Click to expand...
You put in the command the box boots up with the infinity screen. You go through the video wizard, then set your tuners, then network. Does it not start the infinity setup?
 
makido said:
You put in the command the box boots up with the infinity screen. You go through the video wizard, then set your tuners, then network. Does it not start the infinity setup?
Click to expand...
yep, login to box from openwebif terminal, paste from browser, follow the instructions for tuner and network then it asks me to insert usb and initialises it. Infinity continues and now asks me how i want to receive channels, either thru Sat or IPTV. Select IPTV and choose SkyWB skin, then it installs plugins and stalls at configuring the one I mentioned...
 
Johnsmith99 said:
yep, login to box from openwebif terminal, paste from browser, follow the instructions for tuner and network then it asks me to insert usb and initialises it. Infinity continues and now asks me how i want to receive channels, either thru Sat or IPTV. Select IPTV and choose SkyWB skin, then it installs plugins and stalls at configuring the one I mentioned...
Click to expand...
I dont get why its freezing at the same place.
Try leaving it for a few minutes see if it kicks in. Ive run the setup and it just works
 
makido said:
I dont get why its freezing at the same place.
Try leaving it for a few minutes see if it kicks in. Ive run the setup and it just works
Click to expand...
ok will do. it may just take a while, not sure why tho. Was pretty quick on my old star 2s. it's deffo frozen cos the clock is still saying 15:44

gutted! even tried open atv 6.3 but exactly same issue. Looks like I've got a £70 dud on my hands :(
 
Last edited by a moderator:
Johnsmith99 said:
gutted! even tried open atv 6.3 but exactly same issue. Looks like I've got a £70 dud on my hands :(
Click to expand...
I dont know what else to suggest, may have to wait for woosh as he as the h9. He might flash his box and find a problem.
Try an earlier 6.2 it might have the same problem but wont know until you try
 
makido said:
I dont know what else to suggest, may have to wait for woosh as he as the h9. He might flash his box and find a problem.
Try an earlier 6.2 it might have the same problem but wont know until you try
Click to expand...
Ok i'll keep trying. just watched the youtube guide and it should install the picons right after the point where mine freezes. Box was only delivered today too, am gutted
 
Status
Not open for further replies.
Back
Top